Esxi 5.1 installation requirements

Table Minimum System Requirements. Note ACS partitions the available disk space automatically during the installation process. Note It is recommended that you allocate the hard disk size to be greater than GB for the secondary instance, which acts as a log collector. The disk space management mechanism in ACS 5. The actual file size limits are calculated at the time of installation, based on the hard coded relative disk quota configuration percent based , using the disk size as an input.

However, ACS database logs have a fixed size. ACS 5. If you want to change the size of the ACS disk after the installation, complete the following procedure:. While restoring the backed up data, a warning message is displayed when the backup size or ACS view database size exceeds the corresponding disk quota. However, the restore operation will not be interrupted.

In ACS 5. An ACS view log collector node usually requires more space to maintain a database of logs and reports. Therefore, the recommended disk size for the secondary instance, which acts as a log collector server, is GB. When you allocate 60 GB for the log collector server, the view database gets only 5. As a result of this, some of the functionalities may not work properly. The functionalities that may be affected are backup, full backup, incremental backup, logging recovery, purge, database compress operation, and so on.

For example, if the VMware host server has a total of 10 CPU cores, then the sum of the allocated CPU cores for all the VMware instances that are created on that server should not exceed Note It is recommended that if hyper threading is enabled on any one of the VMware hosts, it should be enabled on all the VMware hosts that host the ACS VM as part of the same deployment. Note ACS 5. Install the VMware server with the default options and proper IP address. Step 1 Go to the following link.

You should have valid Cisco. Step 3 Run the installer. Step 4 Log into the VMware server. Figure displays the login window of the VMware server.

The vSphere client window is displayed. Figure Figure vSphere Client Window. Figure displays the VMware vSphere versions. Figure About VMware vSphere. The host uses virtualization software such as ESX server to run the virtual machine. The host provides the CPU and memory resources to the virtual machine to access storage and to connect to the network. Step 1 Log in to the ESX server. Step 2 Click Inventory.

The Name and Location dialog box appears. Step 5 Enter the name you will use to reference the VM, and click Next. Figure Name and Location Dialog Box.

Tip Use the hostname that you will use for your VM host. The Data Storage dialog box appears. Step 6 Choose a data store that has a minimum of GB free space available, and click Next.

Figure Data Storage Dialog Box. The Guest Operating System dialog box appears. The Network dialog box appears. You can use up to four NICs. Figure Network Dialog Box. The Create a Disk dialog box appears. Step 9 Select the disk size as GB in the virtual disk capacity window, and click Next. Note You can configure the minimum virtual disk space requirement to be 60 GB.

There may be a critical issue if you use 60 GB as virtual disk space. You can view the workaround in the troubleshooting section. Figure Create a Disk Dialog Box. The Ready to Complete dialog box appears. Take a backup of the ACS configuration. Reimage the VMware with the thick provisioning storage type. Restore the backup in the newly converted thick provisioned storage VMware.

Figure Ready to Complete Dialog Box. Step 11 Check the Edit the virtual machine settings before completion check box, and click Next. The Memory Configuration dialog box appears. Step 12 Enter MB, and click Next. Figure Memory Configuration Dialog Box. The Number of Virtual Processors dialog box appears. Step 13 From the Number of virtual processors drop-down list, choose 2 if 2 is available , or you can choose any number and click Finish.

Step 14 The virtual machine is installed and will be listed in the VMware drawer, as follows. This can be performed using different methods, depending on your environment.

The Virtual Machine Properties window appears. This section describes how to install ACS 5. To install the ACS 5. Step 2 Insert the ACS 5. Step 3 Store the ACS 5. Step 5 Browse and locate the ACS 5. Move to the console tab. You will lose your cursor control as soon as you enter the console tab. Step 7 Press Enter. The machine restarts with the ACS 5. Here the Installer gathers the system information before start copying the files to the disk.

Here will be the final confirmation you need to give before destroying any data on that disk. Press F11 to continue the installation. Installation begins. Reboot the system to complete the installation. Make sure that you have removed the installation media from the server. Some of the console message while rebooting the system. Now vmware EXSi 5. Many of them wonder that, how to login to the system. You can get login screen by just pressing F2. After logging to the system,you can see there are many options provided for configuring the ESXi and viewing the system logs.

It also provided troubleshooting options as well. Hope you liked it. Thank you for reading this article. Your email address will not be published. Currently you have JavaScript disabled.